SPECIFICATIONS
| Part Number | 0115-4711 |
| Model | SL-26 |
| Series | Warner Electric SL Series |
| Type | Power-On Clutch |
| Rated Static Torque | 80 lb. in. (9.04 N·m) |
| Typical Torque | 65 lb. in. out of the box; 90 lb. in. after burnishing |
| Coil Voltage | 120 VAC |
| Rectifier | Internal (AC input); do not Hi-Pot test |
| Bore | 5/8″ |
| Keyway | .1885-.1905 in. wide; .709-.716 in. key height plus bore |
| Electrical Connection | Lead wires, 18 in. |
| Torque Build-Up Time | 22 ms to 80%; 40 ms to 100% |
| Torque Decay Time | 30 ms to 10% (with suppression diode) |
| Inertia | rotor .362, armature & hub .292 lb. in.² |
| Weight | 28 oz. (1.75 lb.) |
| Air Gap | .005-.020 in. (.127-.508 mm), set at the factory |
| Armature Hub | Tapped holes for bolting on a drive component |
| Mounting | Shaft mounted; restrain the field with a loose-fitting pin through the anti-rotation tab |
| Dimensions (in., see drawing) | A = 2.454 max; B = 0.28; C = 0.472 max; D = 2.645 max; E = 0.999; G = 1.74; H = 1.437; I = 0.51 max; J = 0.19 min; K = 1.75; L = 1.465; O = 0.154 |
| Agency | Coil built with UL recognized materials; RoHS compliant |
| Factory Description | SL-26 120VAC 5/8 CL L |
| Catalog | Warner Electric (Inertia Dynamics) Electric Clutches & Brakes Catalog (P-7874) | |
| Catalog | Warner Electric Fractional HP Clutches/Brakes Catalog (P-1630) |
SERIES DESCRIPTION
Warner Electric SL Series power-on clutches (formerly Inertia Dynamics) mount on one shaft and drive a second, parallel shaft through a pulley, gear or sprocket on the armature hub. Energizing the stationary coil pulls the armature against the rotor to transmit torque; removing power lets the zero-backlash spring pull it clear with no residual drag. Nine sizes, SL-08 to SL-42, cover 2.5 to 250 lb. in. BSL models add ball bearings on the armature and field for higher speeds and side loads.
FEATURES
- Power-on design — torque is produced only while the coil is energized; no residual drag when power is removed.
- Zero-backlash armature with spring release for precise, repeatable engagement.
- Stationary field — no slip rings or brushes to wear out.
- Asbestos-free friction material for long life and quiet operation; corrosion-protected parts.
- UL recognized coil materials; RoHS compliant; 100% Hi-Pot tested.
- Sizes 08-42 with inch or metric bores; lead wires on small sizes, screw terminals on 30 and 42.
SELECTION PROCEDURE
- Size by torque: Pick a size whose rated static torque exceeds the torque your load requires, with a service factor for inertia and cycle rate.
- Match the bore and voltage: Each part number is one bore and one coil voltage; 12, 24 and 90 VDC coils are standard.
- Plan for burnishing: Units reach rated torque after burnishing; out of the box they typically produce somewhat less.
- Use DC power: Filtered full-wave DC gives full torque; a diode across the coil protects the switch.
TYPICAL APPLICATIONS
Office machines, printers, copiers, ATMs, vending equipment, packaging and labeling machines, conveyors and other light-duty drives.
HOW TO ORDER
- Specify Part Number: Order 0115-4711 (SL-26, 120 VAC, 5/8″ bore).
- Verify Coil Voltage: Confirm your supply provides 120 VAC. The unit has an internal rectifier.
- Anti-Rotation: Restrain the field with a loose-fitting pin or bracket through the anti-rotation tab. Do not bolt the tab solid, which preloads the bearings.
- Burnish for Full Torque: New units typically deliver less than rated torque until burnished. Energize at 30-40% of rated voltage and slip the unit for 2-3 minutes, ideally in its final location.
- Arc Suppression: Fit a diode across the coil; published decay times assume one.
Got a Question? We’re Here To Help
- For Manuals, Catalogs & Documentation: See Files Section
- Need More Help? Contact Us

