Warner Electric M0110-2211 SL-11 Power-On Clutch, 24 VDC, 6 mm Bore, Lead Wires

$425.08

Lead time - 1 Week +

  • M0110-2211
  • SL Series Power-On Clutch
  • Model: SL-11
  • Voltage: 24 VDC
  • Static Torque: 6 lb.in. (0.5 lb.ft., 0.68 N·m)
  • Bore: 6 mm

SPECIFICATIONS

Part Number M0110-2211
Model SL-11
Series Warner Electric SL Series
Type Power-On Clutch
Rated Static Torque 6 lb. in. (0.68 N·m)
Typical Torque 5 lb. in. out of the box; 8 lb. in. after burnishing
Coil Voltage 24 VDC
Coil Current .198 A
Coil Resistance 121 Ω
Bore 6 mm
Electrical Connection Lead wires, 12 in.
Torque Build-Up Time 7.2 ms to 80%; 10.5 ms to 100%
Torque Decay Time 11 ms to 10% (with suppression diode)
Inertia rotor .0058, armature & hub .0029 lb. in.²
Weight 3.2 oz. (0.20 lb.)
Air Gap .005-.020 in. (.127-.508 mm), set at the factory
Armature Hub Knurled, for pressing on a pulley, gear or sprocket
Mounting Shaft mounted; restrain the field with a loose-fitting pin through the anti-rotation tab
Dimensions (in., see drawing) A = 1.409 max; B = 0.147; C = 0.396 max; D = 1.16 max; E = 0.507; G = 0.935; H = 0.777; I = 0.38 max; J = 0.122 min; K = 0.875; L = 0.585; O = 0.087
Agency Coil built with UL recognized materials; RoHS compliant
Factory Description SL-11 24VDC 6MM CL

 

pdf icon 1
Catalog Warner Electric (Inertia Dynamics) Electric Clutches & Brakes Catalog (P-7874)
Catalog Warner Electric Fractional HP Clutches/Brakes Catalog (P-1630)

SERIES DESCRIPTION

Warner Electric SL Series power-on clutches (formerly Inertia Dynamics) mount on one shaft and drive a second, parallel shaft through a pulley, gear or sprocket on the armature hub. Energizing the stationary coil pulls the armature against the rotor to transmit torque; removing power lets the zero-backlash spring pull it clear with no residual drag. Nine sizes, SL-08 to SL-42, cover 2.5 to 250 lb. in. BSL models add ball bearings on the armature and field for higher speeds and side loads.

FEATURES

  • Power-on design — torque is produced only while the coil is energized; no residual drag when power is removed.
  • Zero-backlash armature with spring release for precise, repeatable engagement.
  • Stationary field — no slip rings or brushes to wear out.
  • Asbestos-free friction material for long life and quiet operation; corrosion-protected parts.
  • UL recognized coil materials; RoHS compliant; 100% Hi-Pot tested.
  • Sizes 08-42 with inch or metric bores; lead wires on small sizes, screw terminals on 30 and 42.

SELECTION PROCEDURE

  1. Size by torque: Pick a size whose rated static torque exceeds the torque your load requires, with a service factor for inertia and cycle rate.
  2. Match the bore and voltage: Each part number is one bore and one coil voltage; 12, 24 and 90 VDC coils are standard.
  3. Plan for burnishing: Units reach rated torque after burnishing; out of the box they typically produce somewhat less.
  4. Use DC power: Filtered full-wave DC gives full torque; a diode across the coil protects the switch.

TYPICAL APPLICATIONS

Office machines, printers, copiers, ATMs, vending equipment, packaging and labeling machines, conveyors and other light-duty drives.

HOW TO ORDER

  • Specify Part Number: Order M0110-2211 (SL-11, 24 VDC, 6 mm bore).
  • Verify Coil Voltage: Confirm your supply provides 24 VDC filtered, full-wave DC; half-wave DC gives lower torque.
  • Anti-Rotation: Restrain the field with a loose-fitting pin or bracket through the anti-rotation tab. Do not bolt the tab solid, which preloads the bearings.
  • Burnish for Full Torque: New units typically deliver less than rated torque until burnished. Energize at 30-40% of rated voltage and slip the unit for 2-3 minutes, ideally in its final location.
  • Arc Suppression: Fit a diode across the coil; published decay times assume one.
5138237 e1722390771778

Got a Question? We’re Here To Help