Warner Electric SFP425-34-90 SFP-425 Pulley Clutch, 90 VDC, 3/4″ Bore

$1,853.48

Lead time - 1 Week +

  • SFP425-34-90
  • SFP Series Pulley Clutch
  • Model: SFP-425
  • Voltage: 90 VDC
  • Static Torque: 250 lb.in. (20.8 lb.ft., 28.2 N·m)
  • Bore: 3/4″

SPECIFICATIONS

Part Number SFP425-34-90
Model SFP-425
Series Warner Electric SFP Series
Type Pulley Clutch
Rated Static Torque 250 lb. in. (28.25 N·m)
Typical Torque 225 lb. in. out of the box; 275 lb. in. after burnishing
Coil Voltage 90 VDC
Coil Current .124 A
Coil Resistance 722 Ω
Bore 3/4″
Keyway .1885-.1905 in. wide; .836-.844 in. key height plus bore
Electrical Connection Screw terminals
Torque Build-Up Time 45 ms to 80%; 70 ms to 100%
Torque Decay Time 50 ms to 10% (with suppression diode)
Inertia rotor 2.250, armature & hub 4.990 lb. in.²
Weight 94 oz. (5.88 lb.)
Air Gap .005-.020 in. (.127-.508 mm), set at the factory
Output Hub 3 holes 1/4-20 UNC-2B on 3.500 in. bolt circle for your pulley or sprocket
Mounting Shaft mounted; restrain the field with a loose-fitting pin through the anti-rotation tab
Dimensions (in., see drawing) A = 3.350 max; B = 0.000 max; C = 0.267; D = 4.015 max; E = 2.999; G = 1.405; H = 0.673; I = 0.645 max; J = 0.188 min; K = 2.500; L = 2.216; N = 0.383; O = 1.810; P = 4.270 max
Agency Coil built with UL recognized materials; RoHS compliant
Factory Description SFP-425 3/4 90VDC CL

 

pdf icon 1
Catalog Warner Electric Fractional HP Clutches/Brakes Catalog (P-1630)

SERIES DESCRIPTION

Warner Electric SFP Series pulley clutches are pre-assembled SF power-on clutches with a bearing-mounted field/rotor and a bearing-mounted output hub that accepts your pulley or sprocket. Slide the unit onto a driving or driven shaft, bolt on the drive component and connect to the load by chain or belt.

FEATURES

  • Power-on design — torque is produced only while the coil is energized; no residual drag when power is removed.
  • Zero-backlash armature with spring release for precise, repeatable engagement.
  • Stationary field — no slip rings or brushes to wear out.
  • Asbestos-free friction material for long life and quiet operation; corrosion-protected parts.
  • UL recognized coil materials; RoHS compliant; 100% Hi-Pot tested.
  • Pre-assembled with the air gap set at the factory.
  • Output hub with three tapped holes on a bolt circle for your pulley or sprocket.

SELECTION PROCEDURE

  1. Size by torque: Pick a size whose rated static torque exceeds the torque your load requires, with a service factor for inertia and cycle rate.
  2. Match the bore and voltage: Each part number is one bore and one coil voltage; 12, 24 and 90 VDC coils are standard.
  3. Plan for burnishing: Units reach rated torque after burnishing; out of the box they typically produce somewhat less.
  4. Use DC power: Filtered full-wave DC gives full torque; a diode across the coil protects the switch.

TYPICAL APPLICATIONS

Conveyors, packaging and labeling machines, feeders, and other belt or chain drives that need on-demand engagement.

HOW TO ORDER

  • Specify Part Number: Order SFP425-34-90 (SFP-425, 90 VDC, 3/4″ bore).
  • Verify Coil Voltage: Confirm your supply provides 90 VDC filtered, full-wave DC; half-wave DC gives lower torque.
  • Anti-Rotation: Restrain the field with a loose-fitting pin or bracket through the anti-rotation tab. Do not bolt the tab solid, which preloads the bearings.
  • Burnish for Full Torque: New units typically deliver less than rated torque until burnished. Energize at 30-40% of rated voltage and slip the unit for 2-3 minutes, ideally in its final location.
  • Arc Suppression: Fit a diode across the coil; published decay times assume one.
5138237 e1722390771778

Got a Question? We’re Here To Help